Cooper Security M-Series Manuel d'instructions Page 29
- Page / 71
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
496478 23
3. Installation
The terminals on the 9750 control unit main pcb are described as Safety
Extra-Low Voltage circuits (SELV), according to the definitions in Safety
Standard EN60 950.
The terminals on the built in communicator are described as SELV or Tel-
ecommunications Network Voltage (TNV) according to the definitions in
Safety Standard EN60 950.
Note: The SELV and TNV connections which are shown in Figure 16 are for refer-
ence only and do not appear on the 9750 main pcb.
It is important that the installer ensures that TNV terminals are connected
ONLY to the PSTN or other circuits designated as TNV circuits. SELV
terminals must be connected ONLY to other circuits designated as SELV
circuits. Strict adherence to the installation instructions will ensure that the
equipment continues to comply with safety regulations to which it was ap-
proved.
Connecting the Telephone Line
Direct connection, or interconnection via other apparatus, to the terminals on
the built in communicator can produce hazardous conditions on the tel-
ephone network. Always seek advice from a competent telephone engineer if
in any doubt regarding connection to these terminals.
The person responsible for connection of the built in communicator to a
PABX system must be as follows:
a) If the wiring is owned by British Telecom PLC, British Telecom must
connect the wiring to the communicator.
b) If the wiring is not owned by British Telecom, either:
(i) British Telecom
(ii) The authorised maintainer
(iii) A professional installer after 14 days written notice to the author-
ised maintainer.
Connect the telephone line as follows (see Figure 17):
1. Using a three core cable (type 1/05mm CW1308), strip back 5mm of
two cores and feed through one of the cable entries in the rear of the
9750 casing. Connect the two cores to the terminals, A and B on the
built communicator.
2. Connect the cable from the A and B terminals on the built in communi-
cator to the corresponding terminals on the BT master box.
3. If other apparatus is required to share the telephone line with the built in
communicator (series apparatus), connect the main apparatus to the
series switched line connections marked A1, B1.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496478 iii 5
- 1. INTRODUCTION 7
- Figure 1. 9750 System Layout 8
- 496478 3 9
- 4 496478 10
- System Features 11
- Detectors 11
- 9755 Hardwired Expander 11
- 9955 Radio Expander 11
- User Control 12
- 2. Technical Description 13
- Control Unit PCB and Case 14
- 9755 Expander 15
- Compatible Equipment 16
- 3. INSTALLATION 17
- Fitting a 9930 LCD Keypad 18
- 496478 13 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- Connecting Keypads 22
- Exit Terminate Button 22
- Sounders 22
- Detector Circuit Connections 23
- Connecting a 9755 Expander 23
- Using Programmable Outputs 24
- Wiring Keyswitches 25
- Installing a Communicator 26
- Statutory Information 27
- Application 27
- Compatible PABXs 27
- Approval 27
- Safety Notice 28
- Connecting the Telephone Line 29
- 24 496478 30
- 496478 25 31
- Fitting a Battery 32
- Initial Start Up 33
- 28 496478 34
- 4. Programming 35
- 30 496478 36
- 496478 31 37
- 32 496478 38
- * See “5. Testing” 39
- Communications Programming 40
- 496478 35 41
- Leaving Programming Mode 42
- Engineer Reset 42
- Re-entering Programming Mode 42
- Programming Reference 43
- 38 496478 44
- 496478 39 45
- RedCare Reset (Command 23) 46
- Status Display (Command 28) 47
- System Reset (Command 33) 47
- PA Reset (Command 34) 48
- Alarm Abort (Command 36) 48
- 496478 43 49
- CSID Code (Command 50) 50
- 496478 45 51
- 46 496478 52
- 496478 47 53
- Call Mode (Command 101) 54
- Reporting Type (Command 103) 55
- Dynamic Test (Command 108) 56
- Download Mode (Command 110) 57
- Rings to Answer (Command 112) 57
- 52 496478 58
- 496478 53 59
- Report Mode (Command 131) 60
- 496478 55 61
- 56 496478 62
- 5. Testing 63
- 58 496478 64
- 496478 59 65
- 60 496478 66
- 64 496478 70
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security M-Series
(36 pages)Scarlett SC-214 manuály
Uživatelské manuály a uživatelské příručky pro Váhy Scarlett SC-214.
Poskytujeme 1 manuály pdf Scarlett SC-214 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels