Cooper Security 9751 Guide de l'utilisateur Page 31
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2. Programming Commands
497096, issue 3 Page 25
50: CSID Code
To enable the user to use the "Remote Reset" facility (enabled with Command
23), you must program the control unit as "Engineer Reset" (Command 33
option 1) and install a four-digit Central Station Identification (CSID) code:
1. Contact the Alarm Receiving Centre (ARC) and obtain the CSID code.
2. Ensure that the system is in installer mode.
3. Select Command 50 and enter the four-digit CSID code.
The control unit now contains the same CSID code as the ARC and can use
this to generate a four-digit reset code that will be recognised by the ARC
7300 Remote Reset decode programmer.
After an alarm, the user keys in their access code to silence the alarm but
cannot reset the system. The system generates the reset code and displays it
on the keypad. The user calls the ARC and reports the reset code. The ARC
verifies the user's identity and then enters the reset code into the 7300
programmer, which generates an anti-code. The ARC gives the anti-code to
the user, who keys it into the keypad to reset the system.
Note: To delete a CSID code, key in "0000" over the existing code.
51: Set Time and Date
The system has an internal clock/calendar, which it uses to record the time
and date of events in the log. This command sets the current time and date in
the clock/calendar. The system displays the date first: enter the day, month
and year in turn, each as two digits. The system then displays the time: enter
the hours and minutes in turn, each as two digits (using the 24-hour clock).
52: Omit Alarm
This command specifies whether, when a user omits a zone, the control unit
omits the tamper contacts as well as the alarm contacts.
Option
0 The control unit omits alarm contacts only.
1 The control unit omits both alarm and tamper contacts.
Note: To permit the user to omit a zone, you must set attribute
X
4 for the zone.
53: Abort User/Engineer Reset
This command specifies how the system is reset after an aborted alarm.
Option
0 Use the reset option selected for the system with Command 33
(default).
1 Permit the user to reset after an abort.
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels