Cooper Security 9853 Guide d'installation Page 28
- Page / 102
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
22 496791
3. Installation
Momentary or Continuous Keyswitches
The 9928 can be connected to either momentary or continuous keyswitches,
see Figure 18. When using a momentary keyswitch remove the jumper from
link M/C. When using continuous keyswitches fit a jumper to link M/C.
Using a Communicator
The 9851 has an internal communicator. If necessary the control unit can
also be fitted with either a communicator plugged on to the main PCB, or
connected to a separate communication device using a wiring harness
connecting to interface pins on the main PCB. Use programming commands
101 to 158 to set up the communicator.
Internal Communicator
The internal communicator is a 2400 Baud Auto Dialling Modem. The com-
municator can be used for:
• Transmitting alarm signals to alarm receiving equipment at a central
monitoring station using either Scancom Fast Format, Scancom SIA
(Security Industry Association), or Contact ID.
• Connecting to a PC based at a remote engineering centre. By using
Scantronic <Downloader> software, the remote PC can up- or download
system parameters (including the event log and diagnostics), set and
unset the alarm system, and carry out other special functions.
Telephone Line
The internal communicator can be connected directly to an ex-directory line
used exclusively for alarm communications.
Where an exclusive line is not available and other apparatus is connected to
the line, for example an answer machine, the internal communicator provides
a series connection with line divert for the other apparatus. When triggered,
the communicator seizes the line and disconnects the other apparatus while
the communicator is operational. When the communicator has shut down, it
reconnects the other apparatus.
Note: Ideally, no other equipment should be connected to an exclusive line.
Three Way Calling
The 9851 also provides a Three Way Calling facility to make sure the internal
communicator can always use a shared telephone line.
To use this facility, the local exchange must provide the Three Way Calling
service on the customer's line.
Line Monitoring
The 9851 provides a Line Monitor function programmed by command 106 to
ensure that the telephone line is connected and working, and to indicate a
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9853
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.911 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels