Cooper Security 9853 Guide d'installation Page 50
- Page / 102
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
44 496791
Restoring All Factory Default Programming
If you wish to restore all factory default options then:
1. Enter programming mode (if you are not already there).
2. Key in 98 at the keypad.
The display shows:
3. Press 1 at the keypad.
The display shows (for example):
4. Either: Press 1 to create a partitioned system
Or 0 to create a single system.
The display shows (for example):
5. Press .
The keypad gives a double confirmation tone and the system loads the
factory default Command values, erasing all previously programmed
values.
Notes:The log is protected and cannot be erased by the Installer.
Programming Reference
Country Defaults (Command 0)
Use this Command to select the country and PTT defaults (to select lan-
guage see Command 126). Note that the system will ask for confirmation and
you must press 1 to end the Command. Note that this Command loads
default access codes and programming options. See “Programming Com-
mands” for details of the options available.
Note: If you select options 5, 6 or 7 (Norway, Sweden or Denmark) then the
control unit also changes the method of entering programming mode. See
“Entering Programming Mode” at the beginning of this chapter.
Zone Programming (Commands 01 to 16, X17 to X40)
The zone programming Commands 01 to 40 take three or more digits. The
first two digits describe the zone type, subsequent digits describe the zone
attributes.
The format for a zone Command number changes, depending on whether the
zone is connected to the control unit or to an expander. For the first 16 zones
key “01” to “16” and press . For zones 17 to 40, which are connected to
expanders, key in “ 17” to “ 40”) and then press .
When you key in the zone number and press the display shows the zone
number and any text caption for the zone. At this point you can edit the zone
text (see below). Press again to start entering the zone types and at-
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9853
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.633 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels