Cooper Security 9853 Guide d'installation Page 54
- Page / 102
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
48 496791
setting and unsetting. If the zone is violated the control
unit starts a tamper alarm, shows the message “AM
Tamper” on the keypad display, and logs the event as a
zone number with Anti Mask.
Forbikobler (FB) (Key in 14). This zone type is a Scandinavian entry/exit
zone. Use this type on zones connected to stand alone
external keypads or access controllers. The zone oper-
ates as a normal entry/exit zone but when triggered by
the external keypad during the exit time the control unit
stops the exit time and sets the system. If the zone is
triggered while the system is set then the control unit
starts the entry time.
Zone Attributes
Specific zone types can have one or more attributes programmed by the digit
after the zone Command and type. (To remove an attribute, key in the
attribute digit again.)
Chime (C) (Key in 1) When enabled by the user, the system gives
a non-alarm warning tone when any zones programmed
as ‘Chime’ are opened. This facility operates only while
the system is unset.
Notes:
1. ‘Chime’ is available only for Normal Alarm, Final Exit, Entry Route and Shock
Analyser zone types.
2. To make chime available from the keypad sounders but not the internal
sounder then program Command 22 with option 0.
Soak Test (S) (Key in 2) Use this zone attribute if you want to place
under long term test a detector that you suspect is giving
false alarms. Zones with this attribute are disabled for 14
days after you return the control unit to user mode. If the
zone is opened while the system is set then the Service
LED glows and the control unit logs the event as a “Soak
Test Fail Zn” (n is the zone number) without sounding any
bells or starting signalling. The Service LED stays alight
until the Engineer resets the system. After midnight on the
14th day the control unit returns the zone to normal use.
Note: Soak test is available only for Normal Alarm, Entry Route, Technical and
Shock Analyser zone types.
Double
Knock (2) (Key in 3) Zones with this attribute will cause an alarm
condition only if one or more sensors generate two alarms
events within a five minute time window, or if one zone
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9853
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.561 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels