Cooper Security 9853 Guide d'installation Page 58
- Page / 102
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
52 496791
If you use option 1 and the user strays from an entry route zone during entry
then the system waits 30 seconds before raising a full alarm. The system
also gives an internal alarm during the 30 second wait.
If the user enters an access code before the end of the 30 seconds internal
alarm then the user can reset the system.
Silent or Audible PA (Command 30)
This Command selects how the system responds when a PA zone operates.
Option 0 (Audible PA) The system operates the sounders and, if a commu-
nicator is fitted, sends a PA message to the ARC.The keypad
displays the PA zone when a user disarms the system.
Option 1 (Silent PA) The sounders stay silent. If a communicator is fitted
the system sends a PA message to the ARC.The keypad displays
the PA zone when a user disarms the system.
Zone Tamper Reset (Command 31)
Use this Command to ensure that the system complies with Scandinavian
requirements for resetting zone tamper alarms while the system is unset.
Use option 0 to allow user reset after a zone tamper.
Use option 1 to enforce engineer reset. The user can silence the alarm, but
the engineer must reset the system by entering the engineering access code,
or by using anti-code or remote reset.
Keypads and Partitions (Command 32)
If you created a partitioned system during initial power up then this Command
allows you to assign entry/exit tones, alarm tones and status displays for one
or more partitions to individual keypads.
To assign each keypad:
1. Make sure you are in programming mode.
2. Key in 32 and press .
The display shows:
3. Press A, B, C or D to assign keypad 1 to the desired partition.
The display shows (for example):
4. Press .
The display shows
5. Repeat steps 3 and 4 for the rest of the keypads.
Notes:
1. By default all keypads belong to all partitions.
2. You cannot assign keyswitches to individual partitions in a partitioned system.
3. Telecommands belong to the whole system in a partitioned system.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9853
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.261 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels