Cooper Security 9751 Guide d'installation Page 29
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
496792 23
3. Installation
Wiring Keyswitches
Figure 16 shows the connections for a 9928 Keyswitch Interface.
Note: You can fit only one keyswitch interface per system.
Momentary or Continuous Keyswitches
The 9928 keyswitch interface can be connected to either momentary or
continuous keyswitches, see Figure 16. When using a momentary keyswitch
remove the jumper from link M/C. When using continuous keyswitches fit a
jumper to link M/C.
Using a Communicator
The 9751 and 9752 control units contain an internal communicator on the
main PCB. In addition the control unit can be connected to a separate
communication device using a wiring harness connecting to interface pins on
the main PCB. Use programming commands 101 to 158 to set up the com-
municator.
Internal Communicator
The internal communicator is a 300 Baud Auto Dialling Modem. The commu-
nicator can be used for:
• Transmitting alarm signals to alarm receiving equipment at a central
monitoring station using either Scancom Fast Format, Scancom SIA
(Security Industry Association), or Contact ID.
• Connecting to a PC based at a remote engineering centre. By using
Scantronic <Downloader> software, the remote PC can up- or download
system parameters (including the event log and diagnostics), set and
unset the alarm system, and carry out other special functions.
Telephone Line
The built in communicator can be connected directly to an ex-directory line
used exclusively for alarm communications.
Where an exclusive line is not available and other apparatus is connected to
the line, for example an answer machine, the built in communicator provides
a series connection with line divert for the other apparatus. When triggered,
the communicator seizes the line and disconnects the other apparatus while
the communicator is operational. When the communicator has shut down, it
reconnects the other apparatus.
Note: Ideally, no other equipment should be connected to an exclusive line.
Three Way Calling
The 9751 and 9752 also provide a Three Way Calling facility to make sure
the built in communicator can always use a shared telephone line.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.931 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels