Cooper Security 9751 Guide d'installation Page 74
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
68 496792
(which represents the “R” or Recall button on a tel-
ephone) which is detected by the exchange as a request
for a new clean line. With the new line available, the
communicator then attempts to connect to the pre pro-
grammed receiver number.
Engineer Download (Command 110)
The control unit can be programmed from a PC using <Downloader> soft-
ware. You can connect the PC to both the 9751 and 9752 control units over
the telephone network. In addition, you can connect the PC to the 9752
control unit locally using a cable.
Use Command 110 to manually connect the control unit to the PC.
Local (0) (9752 only)To connect the control unit to a PC (for exam-
ple a laptop) using a local cable key in 110 0 .
Remote (1) To automatically answer calls coming from a remote PC
over the telephone network key in 110 1 . You will
also need to use Commands 112, 113. (Note that Secure
callback does not work with this option.)
Note: The control unit will leave Command 110 if <Downloader> does not make a
call within 30 minutes.
While the control unit is connected to the PC you can upload its programming
configuration into the <Downloader> in order to inspect it. Using
<Downloader> you can change the configuration and then transmit the new
configuration back to the control unit. If you do not wish to change the con-
figuration you can simply monitor the state of the control unit and zones from
the PC.
Use Command 114 if you want the control unit to answer incoming calls from
<Downloader> without an engineer being present.
Rings to Answer (Command 112)
Use this option to set the number of rings that the system waits before
answering an incoming call from the remote PC. See “Programming Com-
mands” for the available options.
Answer on One Ring (Command 113)
(Answer phone defeat) Use this feature if the alarm system shares a line with
other equipment.
One ring off (0) Disabled
One ring on (1) <Downloader> “warns” the alarm system that a call is
coming by ringing the alarm system number, waiting for
between one and two rings and then hanging up. The
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.129 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels