Cooper Security 9751 Guide d'installation Page 64
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
58 496792
contact with the control unit for more than 15 minutes. If a detector loses
contact for more than two hours the control unit raises an alarm (see Com-
mand 128).
If you select option 0 the control unit will report supervision failure as de-
scribed for Command 128.
Number of Digits in Access Codes (Command 56 (9752 only) )
The 9752 control unit can use either four-digit or six-digit access codes. To
select four digit access codes choose option 0. Select option 1 for six digit
access codes.
Note: Changing from four- to six-digit access codes (or from six- to four-digit access
codes) causes the system to revert to factory defaults for all access codes. Six
digit user code default is 123456 and Engineer code default is 567890.
Battery Load Test (Command 57 (9752 only) )
Use this Command to make the control unit regularly test its backup battery.
Option 0 The control unit does not load test the battery at all.
Option 1 The control unit tests the battery when the system is unset or 23
hours after the last battery test (whichever comes first).
If the battery fails a test then the control unit reports to the central station.
The control unit also gives a regular short tone from the keypad sounders,
and the keypad shows the message “Batt Load Fail”.
Day Tamper Indication (Command 58 (9752 only))
Use this Command if you want the Engineer to reset tamper indications that
occur while the system is unset.
Option 0 The user can reset a displayed tamper while the system is unset.
Note: Use Command 38 to allow the user to reset the system after
a tamper alarm.
Option 1 The Engineer must reset a displayed tamper while the system is
unset. Note that the user can continue to set and unset the system
while a tamper is being displayed.
Sounder Tamper (Command 59)
The control unit can connect to external sounders with one of two tamper
arrangements:
Option 0 The external sounder uses negative voltage tamper return.
Option 1 The tamper return to the external sounder is terminated with a
2K2 resistance.
Select the appropriate option for the sounder fitted to the system.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.696 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels