Cooper Security 9751 Guide d'installation Page 65
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
496792 59
Level B Final Exit Operation (Command 60)
Command 60 controls how the system will treat Final Exit zones in Part Set
Level B. When the Command option is set to 0 any Final Exit zones included
in Part Set B will continue to act as Final Exit zones during Part Set B. When
the option is set to 1 any Final Exit zones included in Part Set B will act as
Normal Alarm zones during Part Set B.
Level B Entry Route Operation (Command 61)
Command 61 controls how the system treats Entry Route zones during Part
Set B. When the option is set to 0 all Entry Route zones included in Part Set
B will continue to act as Entry Routes during Part Set B. When the option is
set to 1 any Entry Route zones included in Part Set B will act as Final Exit
zones during Part Set B.
Level B Exit Mode (Command 62)
Command 62 specifies the exit mode for Level B.
Option 0 The keypad sounders and any internal sounders give a low tone
when entering Part Set Level B. Use Command 65 to select the
exit time.
Option 1 Instant Set (no exit tone)
Option 2 Silent Set. Use Command 65 to program the Exit time. At the end
of the exit time the keypad gives a double beep confirmation tone.
Option 3 Lock Set. See “Level A Exit Mode (Command 39) for an explana-
tion of Lock Set.
Option 4 Level B exit mode is the same as Level A. The system gives full
volume setting tones.
Note that the keypads give a double beep confirmation tone at the end of all
setting modes.
Level B Alarm Response (Command 63)
Command 63 specifies the alarm response for Part Set B.
Option 0 Keypad sounders only
Option 1 Internal sounders and keypad sounders
Option 2 Local alarm (internal and external sounder only)
Option 3 Full alarm (communication and internal/external sounders).
Level B Entry Time (Command 64)
This Command sets the entry time for Level B. See “Programming Com-
mands” for options.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.167 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels