Cooper Security 9751 Guide d'installation Page 70
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
64 496792
3. If Alarm Abort is enabled (Command 36 1) Channel 3 restores if the user
unsets the system.
Dual Ply Entry Warning (Command 86)
Note: Disable Alarm Confirmation (Command 89) to gain access to this Command.
If users habitually exceed the entry time use option 1 to add a 30 second
extension during which the internal sounders give a warning tone. The
extension applies to both Full and Part setting.
If users exceed the dual ply entry warning during full set then the system
gives a full alarm. If users exceed the dual ply entry warning during part set
then the system gives an alarm that is determined by Commands 63 for part
set B, 73 for part set C, or 77 for part set D.
Use Option 0 (default) to disable Dual Ply Entry.
Keypad Dual Key Alarms (Command 87)
This Command allows users to raise a alarms by pressing two keys on the
keypad at the same time. When this facility is enabled (option 1) the alarms
available are:
PA alarm keys 1 and 3
Medical alarm keys 4 and 6
Fire alarm keys 7 and 9
Use option 0 to disable this Command.
Note: this Command also enables PA from keyswitches (See “9928 Installation
Guide”.)
Alarm Confirmation (Command 89)
Option 1 allows you to program the control unit for Alarm Confirmation
(verified alarm), if required by your local Police Intruder Alarms Policy. (Use
this option to comply with DD243: 2002.)
When a detector causes an alarm the control unit activates Channel 3 (Burg).
If the intruder triggers the second detector within the alarm confirm time then
the control unit activates the programmed alarm confirmation channel.
Option 0 disables Alarm Confirmation.
Commands 90 - 97, See “5.Testing”
Load Full Defaults (Command 98)
Use this Command to load default values for all Commands.
1. Enter programming mode (if you are not already there).
2. Key in 98 at the keypad.
The display shows:
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.844 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels