Cooper Security 9751 Guide d'installation Page 79
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
496792 73
No Closing Signal if More Than One Circuit Omitted
(Command 125 (9752 only))
Note: This Command is required for Belgian BVVO approval.
This option is only available if you have selected Scancom Fast format.
When this option is enabled the control unit will NOT transmit a Close signal
if a user has omitted two or more zones.
Select Language (Command 126)
The control unit can display messages on the keypads in one of several
different languages. Use Command 126 to select the language you wish to
use. (To select defaults see Command 0.) The options available are:
Option 0: English (default) Option 5: French
Option 1: Italian Option 6: German
Option 2: Spanish Option 7: Norwegian
Option 3: Portuguese Option 8: Swedish
Option 4: Dutch Option 9: Danish
Radio Zone Supervision Fail Response (Command 128)
If the system is fitted with a 9955 Radio Expander then all the radio zones are
supervised. Should a radio zone not communicate with the 9955 expander
for one hour or more then the 9955 reports a supervision failure to the control
unit. Use Command 128 to select how the control unit will respond to the
reported supervision failure.
Option 0 Full alarm (all sounders and communication to the ARC).
Option 1 Internal, external and keypad sounders.
Option 2 Keypad sounders.
Option 3 Communication to the ARC and no sounders.
Option 4 Prevent the control unit setting until the faulty radio detector
responds to supervision.
Telecommand Requires Entry for Unset (Command 129)
If the system is fitted with a 9955 radio expander then the user can employ a
telecommand to set and unset the system. Command 129 provides two
options for unsetting the system with a telecommand:
Option 0: The user must first trigger the entry zone and start the entry
timer before unsetting the system with a telecommand.
Option 1: The user can unset the system using a telecommand without
first starting the entry timer by triggering the entry zone.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.249 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels