Cooper Security 9751 Guide d'installation Page 63
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
496792 57
displays it on the keypad. The user calls the ARC and tells them the number
shown on the keypad display. The ARC verifies the user's identity, then
enters the code number into a special programmer. The programmer gener-
ates an ‘Anti Code’, which the ARC gives back to the user. The user then
enters the ‘Anti Code’ at the keypad to reset the system.
Note: To delete a CSID code key in “0000” over the existing code.
Setting Time and Date (Command 51)
The system has an internal clock/calendar which it uses to date stamp the
log. To set the system’s clock/calendar to the correct time and date:
1. Enter programming mode (if you are not already there).
2. Key in 51 at the keypad.
The display shows the current date, for example:
3. Key in two digits for the day number and press . Use leading zeros for
the first nine days of the month.
4. Key in the two digits for the month number and press . Use a leading
zero for January to September.
5. Key in the two digits of the year and press .
The display shows the current time, for example:
6. Key in two digits for the hours of the day and press . Use the 24-hour
clock.
7. Key in two digits for the minutes and press .
The keypad sounder gives a double “bleep” and the display shows
“Installer Mode”. The system sets its internal clock/calendar to the time
you have given it.
Omit Tamper Allowed (Command 52)
This Command ensures that the control unit omits the tamper contacts as
well as the alarm contacts when a user omits a zone. Note that you must give
the zone the omit attribute to allow the user to omit a zone.
Option 0 The control unit omits alarm contacts only
Option 1 The control unit omits both alarm and tamper contacts when the
user omits a zone.
Abort Reset (Command 53)
Option 0 Reset after abort is the same as system reset (see Command 33).
Option 1 Enables customer reset after an abort.
BVVO Supervision (Command 54 (9752 only))
If the alarm system must meet BVVO radio supervision requirements then
select option 1. Once selected, the control unit will give a warning on the
keypad display when a user tries to set the system if a detector has lost
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.215 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels