Cooper Security 9751 Guide d'installation Page 75
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
496792 69
alarm system now knows to expect a call within the next
10 to 90 seconds. <Downloader> then rings the alarm
system again, within 10 to 90 seconds. The alarm system
answers after the first ring.
Note: When using "Answer on 1 Ring" set the number of rings in "Rings to Answer"
(C112) to a higher number than that used by the equipment sharing the
telephone line with the alarm system. If you do not, then the other equipment
will never answer any incoming calls.
Access Mode (Command 114)
This function allows you to provide extra security when a remote PC is
dialling into the system. Once the PC is connected to the system then the
<Downloader> has access to all system programming Commands. If you
wish to provide secure access then either use Option 0 or Option 1 below.
Alternatively you can use Command 110 if you want an engineer present to
provide access for a remote PC connection to the panel. Please note that
you cannot use secure callback with Command 110.
Option 0 Call Out Only. Operation: Someone must start a call to the remote
PC manually using Command 0 in User Mode. User Command 0
calls the first <Downloader> telephone number (see Command
118).
Option 1 Secure Callback. Operation: When the remote PC calls, the
system waits for the set number of rings (see Command 112) and
then answers. The remote PC sends a panel ID, the <DOWN-
LOADER> software version, and indicates which of the two
Downloader Telephone Numbers to use (see Commands 118/
119). The system checks that the remote PC is sending the
correct panel ID, and is using the correct <DOWNLOADER>
software version. If these items don't match then the system
hangs up. If the items do match then the system hangs up and,
after a short delay, the system seizes the telephone line and calls
the PC using the indicated Downloader Telephone Number.
Note: Secure Call Back must be Disabled (Default) until the first “attended” upload
has been performed. This first upload can be carried out either using Com-
mand 110 option 1, or using Command 114 option 0.
Option 2 Unattended Mode.
Operation: The control unit answers as soon as the number of
rings set in Commands 112 or 113 have elapsed.
Note: The <Downloader> operator can choose to use Secure Callback, even though
the alarm system is programmed for Unattended Mode.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.664 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels