Cooper Security 9751 Guide d'installation Page 62
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Programming
56 496792
Entry/Exit Tone Volume (Command 45)
Use this Command to set the volume of entry/exit tones from the internal
sounder. If you select option 0 then the internal sounder gives no entry/exit
tones. If you select option 1 then the internal sounder gives quiet entry/exit
tones, while option 9 gives the loudest entry/exit tones. The internal sounder
demonstrates the volume of the tone when you enter the digit.
Tamper Alarm Annunciation (Command 46)
Use this Command to chose which sounders the control unit will activate for
a tamper alarm while the system is unset.
Option 0 Internal sounders only.
Option 1 Keypad sounders only.
Option 2 Internal sounders and keypad sounders.
Lockout Keypads During Entry (Command 48)
This Command is intended to make the system comply with DD243: 2002
6.4.5. If you want the user to unset the system by means of a portable ACE
(for example the 725r telecommand) then the keypads must be locked out
during entry.
Option 0 enables all users at all keypads during entry, option 1 locks out
users from keypads during entry.
When you lockout keypads during entry, various functions are still available:
• Keypad PA, Fire and Medical alarms.
• Duress codes remains active at all times.
• During an alarm the user is not locked out, they can cancel false alarms
or disarm the system.
CSID Code (Command 50)
To allow the customer to use the ‘Remote Reset’ facility, you must program
the control unit as ‘Engineer Reset’ (Command 33 option 1) and then install a
four digit Central Station Identification (CSID) code.
First make contact with the ARC and obtain the CSID code. Then ensure that
the system is in programming mode. Next, key in:
50 nnnn
Where nnnn is the "CSID Code".
The control unit now contains the same CSID code as the ARC. After an
alarm the control unit can generate a ‘Reset Code’ which will be recognised
by the ARC 7300 Remote Reset decode programmer.
After an alarm the user keys in their access code to silence the alarm, but
cannot reset the system. The system generates a four digit code number and
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.356 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels