Cooper Security 9751 Guide de l'utilisateur Page 24
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2. Programming Commands
Page 18 497096, issue 3
33: System User/Engineer Reset
To require an engineer reset, select option 1. To permit a user reset, select
option 0 (the default). Certain types of events always need an engineer reset,
irrespective of the option that you choose here:
° Auxiliary 12V supply fuse blown
° Keypad missing or failed
° Remote expander missing or failed
° A low battery at the control unit.
Note: Compliance with DD 243: 2004 (see page 83) requires that Command 33 is set to
option 1. You can use various other forms of reset, such as remote (see Command
23) or anti-code (see Command 50).
34: PA User/Engineer Reset
To require an engineer to reset the system after a PA, select option 1. To
permit a user to reset the system after a PA, select option 0 (the default).
35: First Circuit Lockout
If you select option 0 (Lockout), the first zone to activate during the set cycle
is ignored until the system is unset. This is the default.
If you select option 1 (Rearm), all zones are included at the end of the
programmed bell run time, provided that the first-to-alarm zone is closed and
the number of rearms is not exceeded. While the zone is open, the system
excludes it. If the zone closes after the system rearms, the system includes it
again.
36: Alarm Abort
Users occasionally trigger false alarms by accident. Select option 1 to permit
them to abort under these circumstances.
If a user accidentally triggers an alarm while the system is set, the control unit
transmits an intruder alarm and starts the Bell Delay and Alarm Abort timers.
To abort the alarm, the user must enter a valid access code during the abort
period. If the user enters a valid code within this time, the system transmits a
restore of the intruder alarm and simultaneously transmits an abort.
Select option 0 (the default) to prevent users from aborting alarms in this way.
Note: The Alarm Abort period is controlled by the Alarm Receiving Centre (ARC).
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels