Cooper Security 9751 Guide de l'utilisateur Page 44
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2. Programming Commands
Page 38 497096, issue 3
26 Pulse Set 1: active for time set by Command 170.
27 Pulse Set 2: active for time set by Command 170.
28 Pulse Set 3: active for time set by Command 170.
29 Pulse Set 4: active for time set by Command 170.
30 Pulse Unset 1: active for time set by Command 172.
31 Pulse Unset 2: active for time set by Command 172.
32 Pulse Unset 3: active for time set by Command 172.
33 Pulse Unset 4: active for time set by Command 172.
34 Fire: active during a Fire alarm.
35 PA: active during a PA.
36 Set Fail: active for 60 seconds from when a set command fails.
37 General Fault: active for all faults except AC Fail, Anti-Mask, Battery
Fault, Line Fault, Supervision Fail, Zone AC Fail, Zone Battery Fault
and Zone Low Battery.
38 All Fault: active for all faults (including AC Fail, Anti-Mask, Aux DC,
Battery Load Test Fail, Battery Missing, Comms Fail, Jamming,
Keypad Ident Fail, Line Fail, Low Battery, Plugby Fail, RF Low
Battery, Supervision Fail, Telecommand Low Battery, uCom Fail,
Zone AC Fail, Zone Battery Fault, Zone Fault, Zone Low Battery and
Zone Pwr O/P).
85: Burglar Communication Rearm
This command determines what happens to the "burg" communications output
(or channel) at the end of the bell run time.
Option
0 Latched (default). The output stays active until an engineer or user
resets the system.
1 Rearm. The system turns off the "burg" channel when the bell run time
has expired. Once the channel is inactive, the system is ready to
report any new alarm.
Note: If Alarm Abort is enabled (Command 36, option 1), the "burg" channel restores if
the user unsets the system.
86: Not used
This command has been replaced by the changed Command 29.
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.259 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels