Cooper Security 9751 Guide de l'utilisateur Page 76
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3. Testing Commands
Page 70 497096, issue 3
Printing the Event Log (9853 only)
Note: 975x models do not have the connector required for event log printing.
To print the event log, make sure the system is in installer mode, and then
press 90y0. To stop printing, press X.
To toggle the logging printer on and off, press 90y7. The keypad gives a
Chime tone when the printer is turned on and a "beep beep" confirmation tone
when the printer is turned off. This is a test mode and is cancelled if power is
lost. Use Command 180 to turn printing on indefinitely.
Figure 2 shows a sample of a printed log.
– 9853 -
14/12/01 18:42:30 Sounder Tamper
<END OF LOG>
Figure 2. Sample Log Print
To print a listing of the control unit's configuration, press 908y
Note: The log is protected and cannot be erased by the Installer or a user.
Event Log Messages
* Printed event messages start with a time and date stamp.
Keypad Display Printed (9853 only)* Meaning
AC Fail AC Lost Mains power supply failed
AC Restore AC Restore Mains power supply restored
Al Conf Dis K== Al Conf Dis K== Alarm confirmation disabled by lock
switch
Al Confirm Z== Confirmed Z== Confirmed alarm on zone ==
Alarm Abort U== Alarm Abort User aborted alarm
AntiMask Al Z== Anti Mask Alarm Z== Anti-mask alarm on zone ==
AntiMask Rs Z== Anti Mask Restore Z== Anti-mask alarm on zone == reset
AntiMask Tp Z== Anti Mask Tamp. Z== Tamper on anti-mask zone ==
ATE L.F. All ATE L.F. All Alarm Transmission Equipment: fault on
all lines
ATE L.F. Rstr ATE L.F. Rstr Alarm Transmission Equipment: line
fault(s) restored
ATE L.F. Single ATE L.F. Single Alarm Transmission Equipment: fault on
one line
AUX DC Fail AUX Trouble Auxiliary power failed
AUX DC Fail Rstr AUX Restore Auxiliary power restored
Bad Checksum EEPROM Failure Control unit memory corrupted
Batt Flt Rstr Battery Restored Battery reconnected
Batt Load Fail Batt Load Test Fail Battery failed load test
Batt Missing Battery Missing Battery disconnected
Bell Tamper Bell Tamper Sounder tampered with
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cooper Security 9751
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.336 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels